Mercedes-Benz-Blog TRIVIA: The History of the S-Class - PART IX


OFFICIAL PRESS RELEASE

Stuttgart, Germany, May 19, 2005

Mercedes-Benz S-Class, 126 series (1979 to 1991)

In September 1979, Daimler-Benz presented a new S-Class generation at the IAA in Frankfurt. The range of models available in the W 126 se-ries was comprised initially of seven vehicles: Choice was from four engines (from the 2.8-liter six-cylinder carburetor unit with 115 kW/156 hp to the 5.0-liter V8 light-alloy engine with direct fuel injec-tion and 176 kW/240 hp) and two body variants – in addition to the normal version, a lengthened variant, as had traditionally been the case with premium-segment sedans for generations. In this case, lengthening of the wheelbase by 140 millimeters was more apparent than otherwise and as usual the extra space served exclusively to in-crease legroom in the rear and the entry width for the rear doors.



In addition to improving ride comfort and safety, development of the new model series focused on decreasing energy consumption. The use of weight-reducing materials and an aerodynamic body optimized in the wind tunnel helped the new S-Class achieve a ten-percent reduc-tion in fuel over its predecessor models. The two eight-cylinder en-gines of the predecessor series were replaced with two redesigned units with larger displacement and light-alloy crankcase. The 5.0-liter engine, which replaced the 4.5-liter cast iron unit, was already familiar as the power unit from the 450 SLC 5.0, while the 3.8-liter light-alloy engine was developed based on the long-serving 3.5-liter V8 with cast iron block. With both higher output and reduced weight, the new V8 engines could now achieve improved performance while at the same time using less fuel. The carburetor and injection versions of the 2.8-liter six-cylinder remained in the range unchanged.

Diesel for export

The W 126 series also saw development of a diesel version for export to the USA. Like its predecessors, the 300 SD Turbodiesel offered a turbocharged 3.0-liter five-cylinder engine, though with output now in-creased by ten hp to 92 kW (125 hp).
Chassis design was essentially the same as for predecessor models. The new S-Class sedans also featured a diagonal swing-axle at the rear and double-wishbone front suspension with zero-offset steering.

The body design incorporated state-of-the-art findings in safety re-search. Thanks to its new design principles the passenger compartment was now able to withstand the so-called “offset crash” un-scathed at a speed of 55 km/h. The W 126-series sedans were the first production cars worldwide to meet the criteria of the frontal offset crash.

Many of the characteristic design elements of the S-Class are to be found beneath the waistline. For the first time, a Mercedes-Benz passenger car had no bumper bars in the classical sense, having instead generously proportioned plastic-coated bumpers that were seamlessly integrated into the car’s front and rear aprons. Broad lateral protective strips made of plastic created a visual link between front and rear aprons, positioned at bumper height between the wheel arches.

A coupe joins the range

At the IAA in Frankfurt of fall 1981, two years after the debut of the W 126 series, an elegant coupe was added to the family, available only with eight-cylinder engines. Both V8 units underwent comprehensive revision as part of the recently initiated “Mercedes-Benz Energy Con-cept”, a program geared to reducing fuel consumption and harmful emissions. In addition to an increase in compression, the list of improvements included camshafts with modified valve timing, air-bathed injection valves and electronic idle speed control. Camshafts with modified valve timing enabled maximum torque to be achieved at a lower engine speed and in the case of the 3.8-liter engine torque was even increased. This unit was subjected to particularly thorough revision: In order to achieve a more favorable volume-to-surface ratio, the bore was reduced and the stroke increased. The modified 3.8-liter V8 thus benefited from a slightly larger displacement. But by way of compensation for their significantly better fuel economy, the two eight-cylinder units were obliged to accept a minor drop in output. In both cases, rear axle ratios were tuned to meet the modified characteristics of the engines. And the two six-cylinder units also saw a whole series of minor modifications that likewise led to fuel economies, even if these were less dramatic. These measures did not affect power output.

Four years after the launch of the Energy Concept the company carried out a comprehensive model refinement package, so that in September 1985, once again at the IAA in Frankfurt, it was able to introduce a completely revised S-Class lineup. In addition to discreet facelifting measures affecting primarily the bumpers, side protection and the wheels, the focus here was above all on restructuring the engine range.

Two newly-designed six-cylinder units, which had been premiered nine months earlier in the mid-range W 124 series, now replaced the trusty 2.8-liter M 110 engine. In the place of the carburetor version came a 2.6-liter direct injection unit, while the parallel-developed 3.0-liter unit became successor to the injection variant of the M 110. A new addi-tion to the range was the 4.2-liter V8 engine, developed by increasing the bore of the 3.8-liter unit and now fitted to the S-Class sedan, the SEC coupe and the SL. The 5.0-liter engine was also modified. Now equipped with an electronic ignition system and the electro-mechanically controlled Bosch “KE Jetronic” injection system, it generated an output of 180 kW (245 hp).

5.6-liter displacement

The most spectacular innovation in the engine range was a 5.6-liter eight-cylinder unit, which was developed by lengthening the stroke of the 5.0-liter V8 and which unleashed an output of 200 kW (272 hp). If required, an even more highly compressed version was also available that delivered a mighty 221 kW (300 hp), although it was not possible to combine this unit with a closed-loop emission control system. But even without catalytic converter this so-called ECE version met emissions standards set down by the Economic Commission for Europe. The models fitted with this engine variant – the 560 SEL and 560 SEC – were in their day the most powerful Mercedes-Benz production cars ever built.

All variants in the revised model range – with the exception of the 560 SEL and 560 SEC in the ECE version – were available on request with a closed-loop emission control system with three-way catalytic converter. In each case the series version was the so-called “catalytic converter retrofit version”, for which the vehicle was delivered without catalytic converter and oxygen sensor, but with the multi-functional mixture preparation and ignition system. These “retrofit versions” could be fitted with the closed-loop catalytic converter without diffi-culty at a later date. This gave customers maximum flexibility in choos-ing the moment to convert their vehicle – a not insignificant advan-tage, given that unleaded gasoline was not universally available at the time. From September 1986 the closed-loop catalytic converter was standard equipment on all Mercedes-Benz passenger car models with gasoline engines; the retrofit versions were available until August 1989 – with a corresponding price discount.

With the introduction of the new model range, the diesel model – which was still reserved exclusively for US export – was replaced by a modified variant. The new 300 SDL was presented with the additional space of the long version and featured an entirely new design of en-gine. This was based on the familiar 3.0-liter six-cylinder unit from the mid-range W 124 series, although this too was equipped with a turbo-charger. The six-cylinder turbodiesel now delivered 110 kW (150 hp) – 44 kW (60 hp) more than the basic version without supercharger and almost 22 kW (30 hp) more than the five-cylinder engine of the prede-cessor model.

As was expected, the running gear of the facelifted models displayed no fundamental modifications. Nevertheless, the rear axle design was modified in a few details in order to improve ride comfort and reduce engine noise. In addition, all models in the W 126 series were now fitted with 15-inch wheels and larger brakes to match. The design of the optional light-alloy wheels – these were only standard equipment on the 560 SEL and 560 SEC – was updated to match those of the compact-class and mid-range model series.

Minor modifications

The other stylistic modifications carried out on the improved models of the W 126 series not only served to update the design, but were also integrated for specific technical reasons. By lowering the aprons it was possible to further reduce front axle lift forces and improve airflow at the rear. This also had the effect of further enhancing directional sta-bility and road adhesion when moving at speed, an aspect of consider-able importance with respect to the performance of the new top-of-the-range 560 SEL.

The lateral protective strips were now smooth in design rather than grooved, and like the bumper system they reached down lower and in-cluded additional trim on the frame side members. As the 5.6-liter models came with wider 215/65 VR 15 tires as standard, unlike their lower-powered sister models, front apron and fender beading were modified in shape in order to create the necessary lateral clearance for the front wheels.

In September 1987, when the S-Class encountered an unusually chilly easterly wind in the form of the BMW 750 i, higher-performance vari-ants of all V8 engines were introduced. Compression ratios in all cases were increased to 10:1, and additional measures were taken to im-prove performance by between six and ten percent depending on the model. The effect was even clearer in the case of the variants with catalytic converters: By optimizing the emission control equipment the designers succeeded in significantly reducing power loss due to the catalytic converter. The ECE version of the 5.6-liter V8 was discontin-ued without a replacement, since as a result of the treatment to in-crease output the catalytic converter retrofit version was now also ca-pable of developing 221 kW (300 hp).

At the Paris Motor Show in September 1988, the model range was ex-panded to include the 560 SE from the W 126 series, thus making the 5.6-liter engine available in a sedan with conventional wheelbase.

A new diesel variant

From June 1989 a new variant with diesel engine was produced, al-though this too was only available in the USA. Production of the previ-ous 300 SDL had already come to an end in September 1987. The 350 SDL model had a new 3.5-liter six-cylinder engine that had been developed by increasing the bore and stroke of the tried-and-tested 3.0-liter unit. The new turbodiesel was designed more for torque than output and, with exhaust gas recirculation and oxidation catalyst, gen-erated 10 kW (14 hp) less than its predecessor in spite of the larger displacement. But the 350 SDL’s 100 kW (136 hp) was more than adequate, especially given the speed limits that applied throughout the USA. Maximum torque was increased by almost 15 percent and was reached at just 2000/min. In June 1990 the 350 SD with a conven-tional wheelbase was introduced to go alongside the 350 SDL.

As was the case with the predecessor series W 116, the eight-cylinder W 126 models were also available as armored variants. Protection de-sign had been further perfected after intensive development work and a total of 1,465 units were produced. Two 500 SEL models are of par-ticularly interest here, both with a wheelbase extended by 200 millime-ters and roof raised by 30 millimeters. The first of these was built in January 1983 and served as an additional representational vehicle in the company’s own car pool. The second was built on commission from the Vatican for the Holy Father and handed over to Pope John Paul II in August 1985.

As successors to the W 126 series, eight W 140 series sedans were in-troduced at the Geneva Motor Show in March 1991. Although the new models went into production only a month later, the plant continued to turn out 126 sedans for export for a while.

Production of most variants came to an end between August and October 1991, although the last few armored models did not come off the production line until April 1992. During the entire 12-year production period a total of 818,036 sedans left the production lines in Sindelfingen, 97,546 of them with diesel engines. That made the W 126 the most successful premium-class series in the history of the company.

The 126 series in the press

Auto, Motor und Sport, Germany, volume 7/1991, on the S-Class: “On driving you quickly realize that at Daimler-Benz quietness is part of civil responsibility. Any mechanical noise – even with the six-cylinders – remains discreetly in the background; in addition it is striking just how comprehensively the Mercedes developers have managed to eliminate wind noise.”

Frankfurter Allgemeine Zeitung, Germany, May 24, 1986, on the Mercedes-Benz 300 SE: “The 300 SE holds its line like a ship on a fixed course. Any unevenness in the road surface is swallowed with ease by the springs and dampers. No other car achieves such a degree of comfort out of steel and rubber. The large steering wheel allows you to corner with caution as well as with joyful abandon. It does everything you want. The running gear reveals unusually high reserves of safety.”























Copyright © 2008, Mercedes-Benz-Blog. All rights reserved.

Bookmark the permalink. RSS feed for this post.

Leave a Reply

Search

Swedish Greys - a WordPress theme from Nordic Themepark. Converted by LiteThemes.com.